Cut the plant at the base of the stalk and hang upside down
from a line or rope until it is dry. If you are in a dry climate, your product
will dry quickly. In Southern California,
for example, it takes 4-5 days. If you are in a humid climate you should have a
moisture-controlled room and it may take longer.
STEP 2: De-BUDDING FROM BRANCHES
After the plant is dry – water leaves and trim around the
buds are brittle) then take off the water leaves first. Cut buds from branches and place in a plastic
bag or container. Discard branches and
STEP 3: TRIMMING BUDS
Make sure the buds have about 5-10% moisture on the
inside. The outside trim around the buds
should be brittle. Place the recommended
amount of product in the mesh barrel on the trimmer. You should have at least 2 inches between the
product and the axle. Never place more than this in the trimmer as it can
overwork your product. Turn the speed control to your desired speed and watch
it tumble for 2-3 minutes. Trimming will start immediately, as you will see
trim passing through the mesh, down through the funnel bag into your catch
bin. Open the zipper in the mesh and
check your buds. Some strains trim in
less than 5 minutes, so don’t over tumble!
If it is not ready, zip up the net and begin tumbling for another 2-3
minutes. Stop and check the buds at any
time in the tumbling; it does not disturb the process. It is more important to
stop tumbling earlier than necessary than it is to over tumble. When the amount of trim begins to slow
through the mesh and you see kief begin to pass through the mess, it is time to
stop tumbling. Your product should be about 85% trimmed at this point, with very
little trichomes or crystal lost. After
you put our trim into another container, put an empty container under the trimmer,
unzip the mesh barrel and turn on the motor until your trimmed product falls into
STEP 4: ISOLATING POPCORN SIZE
Unzip the net completely (only one zipper comes completely
apart; the other stays together by design) and pull the net from the velcro on
the drums. Replace this net with the ¼” mesh net. Put your trim into this net,
zip it up and tumble on high speed. The trim will flow through the mesh quickly
and any popcorn size nuggets will remain in the barrel. Remove the clean trim from below and put a
clean container underneath the trimmer. Unzip the zippers and turn on the motor
to release your popcorn size nuggets into the clean container.
STEP 5: ISOLATING KIEF
Lastly, Replace the ¼” mesh net with the 110 or 151 micron
kief mesh and put a clean catch basin below the funnel flow bag. Freeze your final trim and pour it into the
barrel with the kief mesh. Fill the
barrel until it is to the axle. If you have a dust cover/kief catcher be sure
to put it on the trimmer. Turn the
trimmer on full speed and let it tumble for your desired time or until the kief
stops passing through the mesh. The Kief will slowly pass through the kief mesh
and through the funnel flow bag into your container. It will also be on the inside of the dust
cover and on the funnel flow bag. You
can scrape this or gently wipe it into your container.
luck! If you have any questions, call
Tom’s Tumble Trimmer at 800-601-0797.
Choosing the right model size for you is entirely dependent on two things: 1) your weekly volume and 2) how much you like trimming. While our TTT 1900 is the most popular model in recent years, this model is best for grower who trim 10-40 pounds at a time. It does 2 pounds per cycle. If you trim less than this, the TTT 1600 is for you. If you trim more than this, the TTT 2200 (2-4 pounds per cycle) or the TTT 2600 (3-6 pounds per cycle) are best for you.
TTT Innovations is required by its
distributor to conform with The California Transparency in Supply Chains Act to
disclose efforts to eradicate slavery and human trafficking from direct supply
chains. We take seriously the federal and international efforts to end all
kinds of forced labor-‐
whether in the form of
prison labor, indentured labor, bonded labor, human trafficking or otherwise.
We are committed to fair labor
practices within our supply chain. We will therefore engage aprocesstoidentifyandevaluatethepotentialrisksforhumantraffickingandslaveryinour
supply chain. Prior to partnering with any new suppliers, and annually
thereafter, we will conduct an initial screening of thosesuppliers.
Every year we will examine relevant
information about each supplier to evaluate risks and vulnerability to slavery
or human trafficking in the production of supplier goods.
TTT Innovations requires that direct suppliers
certify that materials incorporated into the product comply with the laws
regarding slavery and human trafficking of the country or countries in which
they are doing business.
TTTInnovationswillmaintaininternalaccountabilitystandardsandproceduresforemployeesor contractors failing to meet company
standards regarding slavery and trafficking. If a
contracted factory is found to violate laws, it is responsible for improving
performance. If the factory fails to
make progress, they are subject to review and sanctions, including potential
termination of any supplier agreements.
Employees and management with direct
responsibility for supply chain management will be provided training on forced
labor, including human trafficking and slavery.
Due to the nature of the product use, there are no returns on trimmers or nets. When used according to our specifications for dryness (brittle) and weight per trimmer, the trimmers work very effectively, as described.
Didn’t find what you were looking for? Contact us.Contact
Sign up to get the latest on sales, new releases and more!